Kyoritsu KEW 2060BT Clamp Power Meter

The Kyoritsu 2060BT power clamp meter has very large drop jaws. The ideal solution for measurements around busbars and large currents.

Features Kyoritsu KEW 2060BT Clamp Power Meter :

Extremely large jaw with tear drop shape:
ideal solution for busbar and large currents!
・Conductor size φ75mm and busbar of 80×30mm or less
・Current up to 1000A rms
・Voltage up to 1000V rms
・Harmonics up to 30th
・Various measurement functions: current, voltage, power, harmonics and phase detection
・LCD can display simultaneously the values of voltage and frequency or power and power factor
・Each degree of harmonics can be shown on the LCD of the tester
・BluetoothⓇ communication functions

１．Various measurement functions

Measurements of current, voltage, power, harmonics and phase detection are possible.
True RMS: Indicates a correct value at the distorted waveform.
Functions of PEAK, MAX, MIN, AVG are available.
Easy to check the temporal change in the power source.
LCD can display simultaneously the values of voltage and frequency or power and power factor.

2．Power measurement

Power measurement on any wiring system is possible.

KEW 2060BT can perform Single-phase 2-Wire / Single-phase 3-Wire and balance and unbalance
measurements of Three-phase 3-Wire

/ Three-phase 4 Wire. The double display can simultaneously show many parameters like
W & PF, W & deg, W & VA, W & Var, V & A, etc.

Various parameters such as active/reactive/apparent power,
power factor, phase differences (1P2W only)
which are required for the power measurement can be measured.

Total 3-phase power can be measured in simple steps.

By setting the CT and VT ratio and measuring the
secondary side of the transformation, the primary side value can be obtained.

3．Harmonics measurement

Harmonics of the voltage and current, which cause various failures at the field, can be measured.
It is possible to measure and show each voltage and current harmonics up to 30th.
Total harmonics distortion factor is in two types of THD-R and THD-F. Each degree of harmonics can be shown on the LCD of the tester. Both the current value (or voltage value) and the content ratio can be displayed on the same screen.

4．Phase detection

5．Connectivity

○Dedicated Application “KEW Power＊” supports both Android™ and iOS.
○LCD display can be checked at the smart devices.
○Measured values and graphs can be stored with a press of a button.
○Voltage and current can be shown in the waveform display. Existence of the harmonics can be found easy.
○Threshhold of each measured value can be set at the applicaion, and PASS and FAIL judgement is possible.

Measurement Data Monitoring Application “KEW Power＊”

Please search “KEW Power＊”
Communication charge may be incurred separately to download application.

Application for iOS
Free iOS software “KEW Power” is available on “APP Store”
Supporting iOS 10.0
Application for Android
Free Android software “KEW Power” is available on “Google Play Store”
Supporting Android Ver. 5 to 10

Specification Kyoritsu KEW 2060BT Clamp Power Meter :

ACV
Wiring connections		1P2W, 1P3W, 3P3W, 3P4W
Measurements and parameters		Voltage, Current, Frequency, Active power, Reactive power, Apparent power, Power factor(cosθ), Phase angle, Harmonics(THD-R/THD-F), Phase rotation

	Range	1000V
	Accuracy	±0.7%rdg±3dgt (40.0 – 70.0Hz) ±0.3%rdg±5dgt (70.1 – 1KHz)
	Crest factor	1.7 or less
ACA

	Range	40.00/400.0/1000A (3 range auto)
	Accuracy	±1.0％rdg±3dgt (40.0 – 70.0Hz) ±2.0％rdg±5dgt (70.1 – 1kHz)
	Crest factor	3 or less on 40.00A/400.0A range, 3 or less 1500A peak on 1000A range
Frequency

	Display Range	40.0 – 999.9Hz
	Accuracy	±0.3％rdg±3dgt
Active power

	Range	40.00/400.0/1000kW
	Accuracy	±1.7%rdg±5dgt (PF1, sine wave, 45 – 65Hz)
Apparent power

	Range	40.00/400.0/1000kVA
	Accuracy	±1dgt against each calculated value Sum: add errors of each channel, 3P3W: ±2dgt, 3P4W:±3dgt
Reactive power

	Range	40.00/400.0/1000kVar
	Accuracy	±1dgt against each calculated value Sum: add errors of each channel, 3P3W: ±2dgt, 3P4W:±3dgt
Power factor

	Display Range	-1.000 – 0.000 – +1.000
	Accuracy	±1dgt against each calculated value Sum: add errors of each channel, 3P3W: ±2dgt, 3P4W:±3dgt
Phase angle (1P2W only)

	Display Range	-180.0 – 0.0 – +179.9
	Accuracy	±3.0°
Harmonics RMS(Content rate)

	Analysis order	1st – 30th order
	Accuracy	±5.0％rdg ± 10dgt (1 – 10th) ±10％rdg ± 10dgt (11 – 20th) ±20％rdg ± 10dgt (21 – 30th)
Total harmonics THD-R/THD-F

	Display Range	0.0% – 100.0%
	Accuracy	±1dgt against the calculated results of each measured value
Phase rotation		ACV 80 – 1100V (45 – 65Hz)
Other functions		MAX/MIN/AVG/PEAK, Data hold, Bluetooth®, Back light, Auto power off
General

	Communication interface	Bluetooth®5.0
	Power source	LR6 (AA) (1.5V) ×2
	Continuous measuring time	Approx. 58 hours
	Conductor size	φ75 mm max. (busbar of 80mm × 30mm)
	Dimensions / Weight	283(L) × 143(W) × 49(D) mm / Approx. 590g (including batteries)
	Applicable Standards	IEC 61010-1, IEC 61010-2-032, IEC 61326-1, -2-2(EMC), IEC 60529(IP40) CAT IV 600V / CAT III 1000V Pollution degree 2
	Included Accessories	7290 (Test leads) 9198 (Carrying Case) LR6(AA)×2, Instruction Manual

Kyoritsu KEW 2060BT Catalogue

Produk asli Kami distributor langsung KYORITSU. Harga murah dan berkualitas bergaransi tentunya. dapat di kirim ke seluruh wilayah indonesia.

Dalam pengiriman produk yang pelanggan beli, sebelumnya sudah kami cek untuk memastikan produk dalam keadaan baik dan siap kirim.

Watch video

Click to enlarge

Back to products

Power clamp meter Kyoritsu 2060BT memiliki rahang berbentuk drop yang sangat besar. Solusi ideal untuk pengukuran di sekitar busbar dan arus besar.

・Ukuran konduktor φ75mm dan busbar 80×30mm atau kurang
・Arus hingga 1000A rms
・Tegangan hingga 1000V rms
・Harmonik hingga 30th
・Berbagai fungsi pengukuran: arus, tegangan, daya, harmonisa,
dan deteksi fase
・LCD dapat menampilkan secara bersamaan nilai voltase dan frekuensi
atau daya dan faktor daya
・Setiap tingkat harmonik dapat ditampilkan pada LCD penguji
・Fungsi komunikasi BluetoothⓇ

KEW CONNECT

CAT4 600V RMS BENAR Φ75 Lampu latar Bluetooth

Description
Layanan Pelanggan

Description

ACV
Wiring connections		1P2W, 1P3W, 3P3W, 3P4W
Measurements and parameters		Voltage, Current, Frequency, Active power, Reactive power, Apparent power, Power factor(cosθ), Phase angle, Harmonics(THD-R/THD-F), Phase rotation

	Range	1000V
	Accuracy	±0.7%rdg±3dgt (40.0 – 70.0Hz) ±0.3%rdg±5dgt (70.1 – 1KHz)
	Crest factor	1.7 or less
ACA

	Range	40.00/400.0/1000A (3 range auto)
	Accuracy	±1.0％rdg±3dgt (40.0 – 70.0Hz) ±2.0％rdg±5dgt (70.1 – 1kHz)
	Crest factor	3 or less on 40.00A/400.0A range, 3 or less 1500A peak on 1000A range
Frequency

	Display Range	40.0 – 999.9Hz
	Accuracy	±0.3％rdg±3dgt
Active power

	Range	40.00/400.0/1000kW
	Accuracy	±1.7%rdg±5dgt (PF1, sine wave, 45 – 65Hz)
Apparent power

	Range	40.00/400.0/1000kVA
	Accuracy	±1dgt against each calculated value Sum: add errors of each channel, 3P3W: ±2dgt, 3P4W:±3dgt
Reactive power

	Range	40.00/400.0/1000kVar
	Accuracy	±1dgt against each calculated value Sum: add errors of each channel, 3P3W: ±2dgt, 3P4W:±3dgt
Power factor

	Display Range	-1.000 – 0.000 – +1.000
	Accuracy	±1dgt against each calculated value Sum: add errors of each channel, 3P3W: ±2dgt, 3P4W:±3dgt
Phase angle (1P2W only)

	Display Range	-180.0 – 0.0 – +179.9
	Accuracy	±3.0°
Harmonics RMS(Content rate)

	Analysis order	1st – 30th order
	Accuracy	±5.0％rdg ± 10dgt (1 – 10th) ±10％rdg ± 10dgt (11 – 20th) ±20％rdg ± 10dgt (21 – 30th)
Total harmonics THD-R/THD-F

	Display Range	0.0% – 100.0%
	Accuracy	±1dgt against the calculated results of each measured value
Phase rotation		ACV 80 – 1100V (45 – 65Hz)
Other functions		MAX/MIN/AVG/PEAK, Data hold, Bluetooth®, Back light, Auto power off
General

	Communication interface	Bluetooth®5.0
	Power source	LR6 (AA) (1.5V) ×2
	Continuous measuring time	Approx. 58 hours
	Conductor size	φ75 mm max. (busbar of 80mm × 30mm)
	Dimensions / Weight	283(L) × 143(W) × 49(D) mm / Approx. 590g (including batteries)
	Applicable Standards	IEC 61010-1, IEC 61010-2-032, IEC 61326-1, -2-2(EMC), IEC 60529(IP40) CAT IV 600V / CAT III 1000V Pollution degree 2
	Included Accessories	7290 (Test leads) 9198 (Carrying Case) LR6(AA)×2, Instruction Manual